Ultrasonic antifouling for ships, yachts & motorboats

Y-Sonic 10 Ultrasonic antifouling prevents the adhesion of algae and mussels for ships up to 10m LWL Infested ship hulls are lastingly protected by algae and mussels. The installation can be done by yourself or by a local shipyard. Position of the click generator for a motor boat, sailing yacht up to 10m LWL (vessel's waterline length) Is an antifouling necessary on the ship, yacht, boat? We always recommend the combination of antifouling with our click system. Nevertheless we have very good references without antifouling, only with our click system, where only the hull is kept free by means of high-precision clicks. Decisive is the concentration of nutrients in the water, a light biofilm remains, but without algae or mussel formation. The hull of yachts, boats and ships thus remains protected against algae infestation. There are experiences where e.g. with a high algae concentration or a worse quality of the gelcoat, hard lacquer, the click tones alone are not enough, just like antifouling. The combination of antifouling with the click system always works better than each system separately. Y-Sonic Ultrasonic antifouling advantages Low energy consumption of 8.4 watts / hour (0.7 ampere at 12 volt) Operation with solar collectors possible Maintenance is reduced to a minimum, annual antifouling coats are no longer necessary Clear hull gliding better through the water thanks to the lower resistance Acts preventively & curatively on GFK, plastic, steel and aluminium hulls Technical specifications Voltage electronic control 12-24VDC / 88-264VAC, 47-63Hz (1m cable with EU connector) Battery discharge protection with automatic restart Power consumption 8.4 Watt / hour Click generator (IP68) signal cable length 4m with plug 3-pole (IP68) Electronics box Dimensions LxWxH 130x130x60mm (IP67, Fibox PC 125/60 HG) Weight 2.3kg EU quality product 2 years warranty electronic control / 5 years warranty click generator The advantages at a glance Scientifically proven effectiveness against all types of algae: existing algae die within a few weeks Ecologically friendly to the environment, no algae agents, chemicals are produced Low power consumption thanks to intelligent technology The devices are maintenance-free, have a high quality and a service life of up to 10 years Get back the full hull speed through and performance Fuel saving thanks less water resistance Reduces costs: water lift outs, hull sanding & re-painting, scrubing the hull underwater during the season More leisure time thanks to reduced maintenance requirements Y-Sonic Mounting & Installation The Y-Sonic Ultrasonic Antifouling Algae Killer is easy to install. The click generator is mounted inside the hull on the outer shell, which is in direct contact with the water. Direct sound transmission to the shell must be ensured. For this purpose, a silicone paste is lightly applied to the head of the click generator. You will find all the information about installation, positioning, mounting and much more in the operating instructions supplied. Grind surface of outer hull Grind the ring & glue to the hull Srew in the Click Generator Anti Algae Click Generator finished Antifouling consulting Depending on the size of the boat, the correct position of the click generator is of utmost importance. We would be happy to advise you on this free of charge and determine the optimal position for the click generator. Just send us a few pictures with the measurements via our contact form algae free consulting.

Y-Sonic 20 Ultrasonic antifouling prevents the adhesion of algae and mussels for ships over 10m in length LWL Infested ship hulls are lastingly protected by algae and mussels. The Y-Sonic 20 is designed for yachts, motorboats and ships over 10m in length. The installation can be done by yourself or by a local shipyard. The picture shows the optimal position of the Y-Sonic Ultrasonic antifouling device: Position of the click generator for a motor boat, sailing yacht up to 20m LWL (vessel's waterline length) Position of the click generator for a motor boat, sailing yacht from 20m LWL Is an antifouling necessary on the ship, yacht, boat? We always recommend the combination of antifouling with our click system. Nevertheless we have very good references without antifouling, only with our click system, where only the hull is kept free by means of high-precision clicks. Decisive is the concentration of nutrients in the water, a light biofilm remains, but without algae or mussel formation. The hull of yachts, boats and ships thus remains protected against algae infestation. There are experiences where e.g. with a high algae concentration or a worse quality of the gelcoat, hard lacquer, the click tones alone are not enough, just like antifouling. The combination of antifouling with the click system always works better than each system separately. Y-Sonic Antifouling Advantage Low energy consumption of 13.2 watts / hour (1.1 ampere at 12 volt dc)  Operation with solar collectors possible Maintenance is reduced to a minimum, annual antifouling coats are no longer necessary Clear Hull gliding better through the water thanks to lower resistance Acts preventively & curatively on GFK, plastic, steel and aluminium hulls Technical specifications Voltage electronic control 12-24VDC / 88-264VAC, 47-63Hz (1m cable with EU connector) Battery discharge protection with automatic restart Power consumption 13.2 Watt Click generator (IP68) signal cable length 4+8m with plug 3-pole (IP68) Electronics box Dimensions LxWxH 130x130x60mm (IP67, Fibox PC 125/60 HG) Weight 3 kg EU quality product 2 years warranty electronic control / 5 years warranty click generator The advantages at a glance Scientifically proven effectiveness against all types of algae: existing algae die within a few weeks Mussels no longer stick, can be easily removed Ecologically friendly to the environment, no algae agents, chemicals are produced Low power consumption thanks to intelligent technology The devices are maintenance-free, have a high quality and a service life of up to 10 years Get back the full hull speed through and performance Fuel saving thanks less water resistance Reduces costs: water lift outs, hull sanding & re-painting, scrubing the hull underwater during the season More leisure time thanks to reduced maintenance requirements Y-Sonic Mounting & Installation The Y-Sonic Ultrasonic Antifouling Algae Killer is easy to install. The click generator is mounted inside the hull on the outer shell, which is in direct contact with the water. Direct sound transmission to the shell must be ensured. For this purpose, a silicone paste is lightly applied to the head of the click generator. You will find all the information about installation, positioning, mounting and much more in the operating instructions supplied. Grind surface of outer hull Grind the ring & glue to the hull Srew in the Click Generator Anti Algae Click Generator finished   Antifouling Consulting Depending on the size of the boat, the correct position of the click generator is of utmost importance. We would be happy to advise you on this free of charge and determine the optimal position for the click generator. Just send us a few pictures with the measurements via our contact form algae free consulting.  

Y-Sonic 50 Ultrasonic antifouling prevents the adhesion of algae and mussels for ships up to 50m LWL length Infested ship hulls are lastingly protected by algae and mussels. The Y-Sonic 50 is designed for yachts, motorboats and ships from 20m to 50m length. The installation can be done by yourself or by a local shipyard. The picture shows the optimal position of the Y-Sonic Ultrasonic antifouling device: Position of the click generator for a motor boat, sailing yacht up to 50m LWL (vessel's waterline length)  Is an antifouling necessary on the ship, yacht, boat? We always recommend the combination of antifouling with our click system. Nevertheless we have very good references without antifouling, only with our click system, where only the hull is kept free by means of high-precision clicks. Decisive is the concentration of nutrients in the water, a light biofilm remains, but without algae or mussel formation. The hull of yachts, boats and ships thus remains protected against algae infestation. There are experiences where e.g. with a high algae concentration or a worse quality of the gelcoat, hard lacquer, the click tones alone are not enough, just like antifouling. The combination of antifouling with the click system always works better than each system separately. Y-Sonic Antifouling Advantage Low energy consumption of 75 Watt, operation with solar collectors possible Maintenance is reduced to a minimum, annual antifouling coats are no longer necessary Clear Hull gliding better through the water thanks to lower resistance Acts preventively & curatively on GFK, plastic, steel and aluminium hulls Technical specifications Voltage electronic control 12-24VDC / 88-264VAC, 47-63Hz (1m cable with EU connector) Battery discharge protection with automatic restart Power consumption 75 Watt Click generator (IP68) signal cable length in total 60m with plug 3-pole IP68 (Define cable length per click generator in the comment field when ordering) Electronics box dimensions LxBxH 410x350x325 mm (IP40) Weight 7.5 kg EU quality product 2 years warranty electronic device / 5 years warranty click generators The advantages at a glance Scientifically proven effectiveness against all types of algae: existing algae die within a few weeks Mussels no longer stick, can be easily removed Ecologically friendly to the environment, no algae agents, chemicals are produced Low power consumption thanks to intelligent technology The devices are maintenance-free, have a high quality and a service life of up to 10 years Get back the full hull speed through and performance Fuel saving thanks less water resistance Reduces costs: water lift outs, hull sanding & re-painting, scrubing the hull underwater during the season More leisure time thanks to reduced maintenance requirements Y-Sonic Mounting & Installation The Y-Sonic Ultrasonic Antifouling Algae Killer is easy to install. The click generator is mounted inside the hull on the outer shell, which is in direct contact with the water. Direct sound transmission to the shell must be ensured. For this purpose, a silicone paste is lightly applied to the head of the click generator. You will find all the information about installation, positioning, mounting and much more in the operating instructions supplied. Grind surface of outer hull Grind the ring & glue to the hull Srew in the Click Generator Anti Algae Click Generator finished Antifouling Consulting Depending on the size of the boat, the correct position of the click generator is of utmost importance. We would be happy to advise you on this free of charge and determine the optimal position for the click generator. Just send us a few pictures with the measurements via our contact form algae free consulting.